It's even better as an app.$3.99 $1.99 · Pay once, no subscriptionDownload on the App Store
SI-ACR Automatic Charging Relay 12/24V 120A (7610)
Blue Sea Systems

SI-ACR Automatic Charging Relay 12/24V 120A (7610)

The Blue Sea Systems SI-ACR Automatic Charging Relay (7610) is a 12/24V DC, 120A relay designed to combine batteries when charging and isolate them when discharging or starting engines. It protects sensitive electronics by isolating house loads during engine cranking and is ignition protected for gasoline-powered boats.

Buy — affiliate linkAdd to my wiring diagram

We earn a small commission on purchases through this link. It does not change what you pay and never affects ratings.

Power
1440 W
Input
12 V DC
Output
12 V DC
!

Safety notes for this component

  • Ensure proper wire sizing to prevent overheating, using the provided chart for charging amps up to 120A.
  • The ACR is not intended to carry starting currents; use a battery switching system for emergency starting.
  • Connect the GND terminal to DC system ground through a one-amp in-line fuse.
  • For start isolation, connect the SI terminal to a line that is positive only when cranking, through a 1-10 amp fuse.

Try it with your setup

How long it takes to charge

At 120 A into a 12 V bank, hours of driving from 20 % to full.

100 Ah bank42 min
200 Ah bank1.5 h
300 Ah bank2.2 h
—

Charge current from rated power ÷ voltage, charge losses and the absorption phase included.

Fine-tune in the charge time calculator →

Wiring it in

Current, fuse and cable size for the SI-ACR Automatic Charging Relay 12/24V 120A (7610) at full rated power.

Supply → charger

DC input · 12 V
Current at rated power
133.3 A
Fuse
175 A ANL
Cable run (one way)CableVoltage drop
1 m95 mm² · 3/0 AWG0.4 %
2 m95 mm² · 3/0 AWG0.8 %
3 m95 mm² · 3/0 AWG1.3 %
5 m95 mm² · 3/0 AWG2.1 %
Other length or voltage? Open the wire gauge calculator →

Charger → battery

DC output · 12 V
Current at rated power
120 A
Fuse
150 A ANL
Cable run (one way)CableVoltage drop
1 m70 mm² · 2/0 AWG0.5 %
2 m70 mm² · 2/0 AWG1 %
3 m70 mm² · 2/0 AWG1.5 %
5 m70 mm² · 2/0 AWG2.6 %
Other length or voltage? Open the wire gauge calculator →

Without a datasheet charge current the output current is rated power ÷ nominal voltage, which can read a little above the label. Copper cable at 20 °C, positive and negative conductor, at most 3 % voltage drop. The cable is always rated for the fuse that protects it, and the fuse is sized at 125 % of the current. Input current assumes 90 % conversion efficiency. If the manufacturer manual specifies a fuse or cable, follow the manual.

Technical data

Nominal Voltage12V DC 24V DC
Start IsolationYes
Amperage Operating Current175mA (combined) 15mA (open)
Terminal Stud Torque140 in-lb (15.82 Nm)
Continuous Rating120A
Intermittent Rating210A (5 min)
Cable Size to Meet Ratings1/0 AWG
Stud MaterialTinned Copper
Terminal Ring Diameter Clearance1.12in (28.45 mm)
Terminal Stud Length0.875in (22.22 mm)
Terminal Stud Size3/8" - 16 (M10)
Combine 30 sec13.6V @ 12 V 27.2V @ 24 V
Combine 90 sec13.0V @ 12 V 26.0V @ 24 V
Open 30 sec12.75V @ 12 V 25.5V @ 24 V
Overvoltage Lockout16.0V @ 12V 32.0V @ 24V
Undervoltage Lockout9.5V @ 12 V 19V @ 24 V
Weight1.25lb (0.57 kg)

Ratings & reviews

No ratings yet — be the first to rate this component.

Sign in to rate and comment
Free account — also saves your wiring diagrams.

Drop the SI-ACR Automatic Charging Relay 12/24V 120A (7610) into your wiring diagram

VoltPlan sizes the cables, picks the fuses and checks the voltages for every component you connect around it.