It's even better as an app.$3.99 $1.99 · Pay once, no subscriptionDownload on the App Store
SmartSolar MPPT 100/30In library
Victron

SmartSolar MPPT 100/30

30 A MPPT charge controller for 12 V and 24 V battery banks with up to 100 V PV input. Bluetooth monitoring, selectable lithium and lead-acid charge profiles, and peak efficiency above 98 %.

★★★★★5.01 rating
Buy — affiliate linkAdd to my wiring diagram

We earn a small commission on purchases through this link. It does not change what you pay and never affects ratings.

Charge current
30 A
PV input
up to 100 V
Output
12 V DC
Price check
≈ €140€4.7 per amp

among the dearest of 4 solar charge controllers in the catalogue (€3–€5 per amp).

Estimated street price; the shop shows today's price.

!

Safety notes for this component

  • Connect the battery before the PV array. The controller reads battery voltage to pick its 12 V or 24 V system setting, and powering it from PV alone can leave it mis-detected.
  • Fuse the battery cable close to the battery positive terminal, sized for the 30 A charge current and the cable you actually fitted.
  • Check array Voc at your coldest expected temperature. Cold derating raises open-circuit voltage, so a string that measures well under 100 V in summer can exceed the limit on a cold clear morning.
  • Not ignition protected. Do not mount it in a compartment that holds petrol or propane.

Try it with your setup

How long it takes to charge

At 30 A into a 12 V bank, hours of full sun from 20 % to full.

100 Ah bank2.9 h
200 Ah bank5.9 h
300 Ah bank8.8 h
—

Datasheet charge current, charge losses and the absorption phase included. Reaching 30 A takes roughly 360 W of panel output; smaller arrays charge proportionally slower.

Fine-tune in the charge time calculator →

Wiring it in

Current, fuse and cable size for the SmartSolar MPPT 100/30 at full rated power.

Charger → battery

DC output · 12 V
Rated charge current
30 A
Fuse
40 A MAXI Blade
Cable run (one way)CableVoltage drop
1 m10 mm² · 8 AWG0.9 %
2 m10 mm² · 8 AWG1.8 %
3 m10 mm² · 8 AWG2.7 %
5 m16 mm² · 6 AWG2.8 %
Other length or voltage? Open the wire gauge calculator →

Copper cable at 20 °C, positive and negative conductor, at most 3 % voltage drop. The cable is always rated for the fuse that protects it, and the fuse is sized at 125 % of the current. If the manufacturer manual specifies a fuse or cable, follow the manual.

Technical data

Maximum charge current30 A
Battery voltage12 / 24 V auto-detect
Maximum PV open-circuit voltage100 V
Maximum PV short-circuit current35 A
Nominal PV power440 W @ 12 V · 880 W @ 24 V
Maximum efficiency98 %
Self-consumption30 mA @ 12 V · 20 mA @ 24 V
Charge voltage 'absorption'14.4 V / 28.8 V (adjustable)
Charge voltage 'float'13.8 V / 27.6 V (adjustable)
MonitoringBluetooth built in + VE.Direct
Power terminals16 mm² / AWG6
Protection categoryIP43 electronics · IP22 connection area
Full output currentup to 40 °C
Dimensions (h × w × d)130 × 186 × 70 mm
Weight1.3 kg

Works with

Verified in VoltPlan diagrams
VictronOrion-Tr Smart 12/12-30 Isolated DC-DC ChargerThe Victron Orion-Tr Smart 12/12-30 Isolated is a galvanically isolated DC-DC charger that charges a 12 V house battery from the alternator with 30 A, 360 W continuous at 40 °C. Input and output are isolated with 200 V DC, which suits boats and separate ground systems. Set-up runs over Bluetooth via VictronConnect.
Charge current
30 A
Input
12 V DC
Output
12 V DC
DCC30S 12V 30A DC-DC Charger with MPPT (RBC30D1S)
RenogyDCC30S 12V 30A DC-DC Charger with MPPT (RBC30D1S)The Renogy DCC30S 12V 30A DC-DC On-Board Battery Charger with MPPT (RBC30D1S) is a 12V charger with MPPT technology. It can charge auxiliary batteries from a vehicle's alternator or solar panels, with a maximum solar input power of 400W.
Charge current
30 A
Input
12 V DC
Output
12 V DC
12V 40A DC to DC Battery Charger (RBC40D1U)
Renogy12V 40A DC to DC Battery Charger (RBC40D1U)The Renogy 12V 40A DC to DC Battery Charger (RBC40D1U) is a 12V charger designed to charge an auxiliary battery from a vehicle's starter battery while driving. It features a maximum rated charge current of 40A and an input voltage range of 9V-16V.
Charge current
40 A
Input
12 V DC
Output
12 V DC
Renogy Rover 40A MPPT Charge Controller
RenogyRenogy Rover 40A MPPT Charge ControllerThe Renogy Rover 40A MPPT Solar Charge Controller is designed for 12V/24V systems. It features MPPT (Maximum Power Point Tracking) technology to optimize solar energy harvesting. The controller has a rated charge current of 40A and a maximum solar input power of 520W for 12V systems and 1040W for 24V systems.
Charge current
40 A
PV input
up to 100 V
Output
12 V DC
★★★★★(1)

Ratings & reviews

5.0
★★★★★
1 rating
5 ★1
4 ★0
3 ★0
2 ★0
1 ★0
Sign in to rate and comment
Free account — also saves your wiring diagrams.
SStefan★★★★★2 months ago

Drop the SmartSolar MPPT 100/30 into your wiring diagram

VoltPlan sizes the cables, picks the fuses and checks the voltages for every component you connect around it.